summaryrefslogtreecommitdiff
path: root/doc/sane-dc240.man
diff options
context:
space:
mode:
authorJörg Frings-Fürst <debian@jff-webhosting.net>2019-07-31 17:00:58 +0200
committerJörg Frings-Fürst <debian@jff-webhosting.net>2019-07-31 17:00:58 +0200
commitd087d778ffb62e2713cb848540bcc819470365bd (patch)
treed69692a274dd1c7d0672e6bb7155a0fc106f9d49 /doc/sane-dc240.man
parentc8bd2513ecba169cff44c09c8058c36987357b18 (diff)
parent3759ce55ba79b8d3b9d8ed247a252273ee7dade3 (diff)
Merge branch 'feature/upstream' into develop
Diffstat (limited to 'doc/sane-dc240.man')
-rw-r--r--doc/sane-dc240.man17
1 files changed, 8 insertions, 9 deletions
diff --git a/doc/sane-dc240.man b/doc/sane-dc240.man
index ba7fd63..70629ab 100644
--- a/doc/sane-dc240.man
+++ b/doc/sane-dc240.man
@@ -14,16 +14,16 @@ connected. The device name is always "0".
.SH CONFIGURATION
The contents of the
.I dc240.conf
-specify the serial port and baud rate to use. The baud rate
+specify the serial port and baud rate to use. The baud rate
specifies the maximum rate to use while downloading pictures. (The
camera is always initialized using 9600 baud, then switches to the
higher rate). On a 450MHz Pentium, I usually have no problems downloading
at 115200 baud, though the camera sometimes has to resend packets due
-to lost characters. Results are better when
+to lost characters. Results are better when
the "interrupt-unmask flag" is set in the IDE driver (hdparm \-u1).
Supported baud rates are: 9600, 19200, 38400, 57600, and 115200.
.PP
-The dumpinquiry line causes some information about the camera to
+The dumpinquiry line causes some information about the camera to
be printed.
.PP
cmdrespause specifies how many usec (1,000,000ths of a) between
@@ -31,7 +31,7 @@ writing the command and reading the result should be used. 125000
seems to be the lowest I could go reliably.
.PP
breakpause is the time in 1,000,000ths of a usec between sending the
-"back to default" break sending commands.
+"back to default" break sending commands.
.PP
Empty lines and lines starting with a hash mark (#) are
ignored. A sample configuration file is shown below:
@@ -82,7 +82,7 @@ to "/tmp/config:" would result in directories "tmp/config", ".", and
.TP
.B SANE_DEBUG_DC240
If the library was compiled with debugging support enabled, this
-environment variable controls the debug level for this backend.
+environment variable controls the debug level for this backend.
A value of 128 requests maximally copious debug output; smaller
levels reduce verbosity.
@@ -101,13 +101,12 @@ The manpage was largely copied from the dc210 manpage.
.SH BUGS
The major limitation that I know of is that the backend assumes
the directory in the camera is 100dc240. Once the camera has
-taken more than 9999 pictures, the directory will increment to 101dc240.
+taken more than 9999 pictures, the directory will increment to 101dc240.
Not only should we check for the additional directory, but pictures may
actually be found in multiple directories.
.PP
More general comments, suggestions, and inquiries about frontends
-or SANE should go to the SANE Developers mailing list
-(see http://www.sane\-project.org/mailing\-lists.html for details).
+or SANE should go to the SANE Developers mailing list
+(see http://www.sane\-project.org/mailing\-lists.html for details).
You must be subscribed to the list, otherwise your mail won't be
sent to the subscribers.
-